Dokuz Eylül Üniversitesi Mühendislik Fakültesi Mühendislik Bilimleri Dergisi, C15/S1 (2013)http://hdl.handle.net/20.500.12397/24522024-03-28T09:48:02Z2024-03-28T09:48:02ZELASTOMER TÜRÜ POLİMERLER İLE MODİFİYE EDİLMİŞ BİTÜMLÜ BAĞLAYICILARIN DEPOLAMA STABİLİTELERİNİN VE REOLOJİK ÖZELLİKLERİNİN İNCELENMESİYILMAZ, MehmetKÖK, Baha VuralKULOĞLU, NecatiALATAŞ, Tanerhttp://hdl.handle.net/20.500.12397/27712020-06-16T12:44:36Z2013-01-01T00:00:00ZELASTOMER TÜRÜ POLİMERLER İLE MODİFİYE EDİLMİŞ BİTÜMLÜ BAĞLAYICILARIN DEPOLAMA STABİLİTELERİNİN VE REOLOJİK ÖZELLİKLERİNİN İNCELENMESİ
YILMAZ, Mehmet; KÖK, Baha Vural; KULOĞLU, Necati; ALATAŞ, Taner
Bu çalışmada, üç farklı polimer katkılı bitümlü bağlayıcının, yüksek sıcaklık depolama stabilitesi özellikleri araştırılmıştır. Bu amaçla iki farklı tür stiren-butadien-stiren (SBSD), (SBSM) ve stiren-etilen-butadien-stiren (SEBS) katkı malzemesi olarak kullanılmıştır. Üç farklı oranda (%2, 4 ve 6) SBS ve SEBS, 160/220 penetrasyonlu bitüme ilave edilerek modifiye bağlayıcılar elde edilmiştir. Saf ve modifiye bağlayıcılara; yumuşama noktası, dönel viskozimetre (DV) ve dinamik kayma reometresi (DKR) deneyleri uygulanarak katkı maddelerinin etkisi belirlenmiştir. Modifiye bağlayıcıların depolama stabilitesi deneyi EN 13399 standardına göre yapılmıştır. Depolama stabilitesi deneyleri sonucunda, elde edilen numunelere saf ve modifiye bağlayıcılara uygulanan deneyler yeniden uygulanmış ve modifiye bağlayıcıların depolanma özellikleri tespit edilmiştir. Elde edilen sonuçlardan, polimer oranı arttıkça viskozite, yumuşama noktası ve kompleks modülü (G*) değerlerinin arttığı belirlenmiştir. Depolama stabilitesi deneylerinden ve reolojik özelliklerin incelenmesinden en iyi sonuca SBSM katkı maddesinin sahip olduğu belirlenmiştir. In this study the high temperature storage stability properties of bituminous binder modified by three different polymers were investigated. For this purpose two different type of styrene-butadiene-styrene (SBSD), (SBSM) and styrene-ethilene-btadiene-styrene (SEBS) were used. The modified binders were obtained by adding three percentage (2%,4%,6%) of SBS and SEBS to 160/220 penetration grade bitumen. The effects of additive materials were determined by applying the softening point, rotational viscosimeter (RV) and dynamic shear rheometer (DSR) tests to virgin and modified binders. The storage stability test of modified binders were carried out according to EN 13399 standard. The tests applied to pure and modified binders were carried out to specimens obtained from at the end of this processes therefore the storage stability properties of modified binders were determined. According to the obtained results it was determined that the values of viscosity, softening points, and complex modulus (G*) were increased by the increase of polymer content. SBSM gave the best result at the end of the storage stability tests and rheological properties.
2013-01-01T00:00:00ZX ÇAPRAZLI ÇELİK SİSTEMLERDE BASINÇ ÇUBUĞUNUN ELASTİK BURKULMA DAVRANIŞININ İNCELENMESİSEÇER, MUTLUUÇAR, TANERhttp://hdl.handle.net/20.500.12397/27702020-06-16T12:44:36Z2013-01-01T00:00:00ZX ÇAPRAZLI ÇELİK SİSTEMLERDE BASINÇ ÇUBUĞUNUN ELASTİK BURKULMA DAVRANIŞININ İNCELENMESİ
SEÇER, MUTLU; UÇAR, TANER
Çelik yapılarda, X çaprazlar deprem yüklerinin karşılanmasında ve yatay yer değiştirmelerin sınırlandırılmasında kullanılmaktadır. Bu çalışmada, çelik X çaprazların çekmeye çalışan elemanı basınç çubuğuna tutturulmuş eşdeğer elastik bir yay eleman olarak modellenmiştir. Basınç çubuğu, farklı uç koşul durumları dikkate alınarak incelenmiş ve kritik burkulma yükü ile bu yükü maksimum yapan mafsalın konumu her durum için ayrı ayrı belirlenmiştir. Ayrıca, herhangi bir nedenle çekme çubuğunun sisteme olan katkısını kaybetmesi durumunun incelenmesi amacıyla sistem elastik yay etkisi dikkate alınmadan modellenmiş ve ara noktasında mafsal olan basınç çubuğu durumu farklı uç koşullarına bağlı olarak incelenmiştir. Mafsalın optimum konumu ve buna karşılık gelen en büyük elastik burkulma yükü belirlenmiştir. Çalışmada elde edilen karakteristik denklemler kullanılarak sayısal örnek incelenmiş ve elde edilen sonuçlar grafikler ve tablolar halinde sunulmuştur.In steel structures, X braces are used for providing lateral resistance to seismic forces and minimizing lateral drifts. In this study, tension member of the X braced steel system is modeled as an equivalent elastic spring which is attached to the compression member. The critical buckling load of the compression member and the optimal place of the hinge that maximizes the buckling load are determined for many end conditions. Additionally, tension member is neglected and the system is remodeled as compression member with an intermediate hinge in order to investigate the loss of tension member due to any reason for various end conditions. The optimal place of the hinge and the maximum elastic buckling load for the spot is also determined. A numerical example is investigated by using the characteristic equations obtained from the study and the results are presented in tables and graphics.
2013-01-01T00:00:00ZTiC KAPLAMALI TAKIMLA İŞLENEN AISI 303 VE AISI 410 PASLANMAZ ÇELİKLERİN İŞLENEBİLİRLİK ÖZELLİKLERİNİN DEĞERLENDİRİLMESİBAHÇECİ, ErsinÖZER, Alpayhttp://hdl.handle.net/20.500.12397/27692020-06-16T12:44:36Z2013-01-01T00:00:00ZTiC KAPLAMALI TAKIMLA İŞLENEN AISI 303 VE AISI 410 PASLANMAZ ÇELİKLERİN İŞLENEBİLİRLİK ÖZELLİKLERİNİN DEĞERLENDİRİLMESİ
BAHÇECİ, Ersin; ÖZER, Alpay
Bu çalışmada, östenitik (AISI 303) ve martensitik (AISI 410) olmak üzere iki farklı mikro yapıya ve kimyasal bileşime sahip paslanmaz çelik malzemelerin işlenebilirlik özellikleri araştırılmıştır. İşlenebilirlik deneyleri kuru tornalama ortamında gerçekleştirilmiştir. Deneylerde 0.12 mm/dev ilerleme hızı ve 1.2 mm talaş derinliği sabit tutulmuş, kesici uç olarak TiC kaplı sementit karbür takım kullanılmıştır. İşlenebilirlik özelliklerinden tornalama kuvvetleri, talaş formu ve yüzey pürüzlüğü incelenmiştir. Kesme hızına bağlı olarak farklı kesme kuvvetleri ve yüzey pürüzlülüğü değerleri elde edilmiştir. Her iki malzeme için artan kesme hızı ile birlikte tornalama kuvvetleri azalmıştır. Kimyasal bileşiminde yüksek orandaki sülfür içeren östenitik paslanmaz çelik (AISI 303), martensitik paslanmaz çelik (AISI 410) malzemeye göre daha düşük tornalama kuvvetleri ve yüzey pürüzlülük değerleri vermiştir.In this study, machinability properties of stainless steel materials having two different microstructures and chemical compositions, namely austenitic (AISI 303) and martensitic (AISI 410), were investigated. Machinability studies were carried out in dry turning conditions. In experiments, cemented carbide tool coated with TiC was used and, feed rate and depth of cut were kept constant at 0.12 mm/rev and 1.2 mm consequently. Turning forces, chip forms and surface roughness were examined as machinability properties. Different cutting forces and surface roughness were obtained depending on cutting speeds. Turning forces decreased with increasing cutting speed for both materials. Because of the high ratio of the sulphur in austenitic stainless steel (AISI 303) lower turning forces and surface roughness were abtained for this steel than the martensitic stainless steel (AISI 410).
2013-01-01T00:00:00ZSİLİS DUMANI VE UÇUCU KÜL KATKILI KENDİLİĞİNDEN YERLEŞEN BETONLARIN TAZE BETON ÖZELLİKLERİ VE BASINÇ DAYANIMLARITOHUMCU, İlhanBİNGÖL, A. Ferhathttp://hdl.handle.net/20.500.12397/27682020-06-16T12:44:36Z2013-01-01T00:00:00ZSİLİS DUMANI VE UÇUCU KÜL KATKILI KENDİLİĞİNDEN YERLEŞEN BETONLARIN TAZE BETON ÖZELLİKLERİ VE BASINÇ DAYANIMLARI
TOHUMCU, İlhan; BİNGÖL, A. Ferhat
Kendiliğinden yerleşen betonlar (KYB), geleneksel betona oranla işlenebilirlik, işçilik maliyetindeki azalmalar ve yüksek dayanım gibi önemli faydalar sağlayan beton teknolojisindeki gelişmelerdendir. KYB üretiminde yüksek oranda su azaltıcı süperakışkanlaştırıcı kimyasal katkılar, fazla miktarda toz malzeme ve/veya viskozite düzenleyici katkı maddesi kullanılmalıdır. Kendiliğinden yerleşme yeteneği; doldurma yeteneği, ayrışmaya karşı direnç ve geçiş yeteneği olmak üzere 3 parametre ile karakterize edilebilir. KYB üretiminde toz malzeme olarak genellikle kireçtaşı tozu, uçucu kül, granüle yüksek fırın cürufu ve silis dumanı kullanılmaktadır. Bu çalışmada mineral katkı maddesi olarak çimento yerine ağırlıkça % 5, % 10 ve % 15 oranlarında silis dumanı ve % 25, % 40 ve % 55 oranlarında uçucu kül kullanılarak KYB üretilmiş ve taze beton özellikleri ile sertleşmiş betonların 3, 7 ve 28 günlük basınç dayanımları belirlenmiştir. silis dumanı ilavesi basınç dayanımlarında artışa yol açarken uçucu kül katkılı betonlarda dayanım azalmaları tespit edilmiştir. En yüksek basınç dayanımı değeri 88 MPa değeri ile %15 silis dumanı kullanılarak üretilen betonlardan elde edilmiştir.Self Compacting Concrete, is one of the developments in concrete technology, which have important benefitsas workability, labor cost reductions and high-strength, compared to traditional concrete. In SCC production, high-range water reducing super plasticizer chemical additives, powder material and/or viscosity regulators additive must be used. Self-settlement capability may be characterized with 3 parameters; filling ability, resistance to decomposition and, passing ability between reinforcement bars. Limestone powder, fly ash, granulated blast furnace slag and silica fume is used as a powder material in SCC production. In this study SCC were produced with using silica fume instead of cement by weight, by the ratios of 5%, 10% and 15%, and fly ash with the ratios of 25%, 40% and 55%. Fresh concrete properties and 3, 7 and 28 days compressive strengths were determined. While SF increased compressive strength, addition of fly ash, on the contrary, decreased it. The highest compressive strength was observed from the concrete specimens with using 15% silica fume, with the value of 88 MPa.
2013-01-01T00:00:00Z